Reloading Supplies

LEE LARGE CUTTER & LOCK STUD8-32 THREADED CUTTERFEATURES-Large cutter with 8-32 thread shank-For use on popular powered case preparation centers

LYMAN AMMO CHECKER 9MM LUGERALUMINUMFEATURES:-Gauges that verify the quality & consistency of both reloaded & factory ammo-Machined from solid aluminum & cut w/ custom tooling to SAAMI minimum chamber tolerances-Just drop your cartridge into...

LYMAN AMMO CHECKER 20 GAUGEALUMINUMFEATURES-For 20 gauge-Check the quality and consistency of both reloaded rounds and purchased ammunition-Allow a reloader to quickly confirm that their ammunition will fit in their chamber-Machined from solid blocks of...

LYMAN CASE NECK DIPPER KITFEATURES-Helps to prolong case life & make the resizing process easier by cleaning & lubricating the interior of bottleneck cartridge cases-Includes 3 brushes to fit in cases from 17 to 45 caliber cases & 1 ounce of...

LYMAN AMMO CHECKER 6.5 GRENDELALUMINUMFEATURES:-Gauges that verify the quality & consistency of both reloaded & factory ammo-Machined from solid aluminum & cut w/ custom tooling to SAAMI minimum chamber tolerances-Just drop your cartridge...

MEC WAD FINGER 20GAFEATURES-20 Gauge-Funnels the was through the crimp & into the wad chamber of the casing-Fits all older MEC reloaders produced before 1983

PETERSON UNPRIMED CASES22CM 50PACK 10BX/CS

HSM BULLETS .380 CAL .356100GR HARD LEAD-RNFP 250CT

MEC 600 PRIMER PAD SPRINGFEATURES:-Used on all single stage machines for repriming your shell

The controlled expansion of the XTP Hollow Point is 1.5x its original diameter over a wide range of velocities. It features a heavier jacket, which stands up to the high pressures and velocities of the highest performance handgun.

This Wad Guide Finger is for use with the 600 JR reloading press.

Lee 45 ACP Case Length Gauge is a precise, easy way to trim to length and square the case mouth. Used with the Cutter and Lock Stud or Zip Trim. Trim to length .888 to .898 inches.

The smokeless Ball Powder 760 has ideal flow characteristics that give it an advantage over other propellants with similar burn rates. 760 is recommended as an excellent choice for 22-250 Remington, 300 Winchester Magnum, as well as 300 WSM.

RCBS Single Stage shell holders are built from hardened steel and designed to properly align the case with the reloading die in single-stage and turret presses. They're sized to fit specific case heads and capture 0.125 inch of the case head for proper...

MatchKing Bullets are Sierra's pre-eminent target bullets. The driving motivation for the design of each MatchKing bullet is accuracy. These bullets have very thin jackets drawn to an exacting concentricity standard of 0.0003 in maximum variation and...

Modeled after the legendary XTP bullet design, HAP (Hornady Action Pistol) bullets are further refined into the perfect competition projectile. While XTP bullets use folds and a cannelure to aid in controlled expansion and terminal performance, Hornady...

If you cast your own bullets, our crimp-on gas checks will enhance their performance. During sizing, the gas check crimps to the base of case lead bullets to seal gasses and protect the base from deformation. Hornady gas checks are the only real choice...

RCBS's 3-Die Carbide Sets for straight-wall rifle and pistol cases. The Carbide Sizer Die sizes the case and de-primes (the carbide sizer ring eliminates the need to lubricate). Its Expander Die expands the case to the proper diameter to accept the...

Alliant Reloder 22 is a top-performing powder for big game loads provides excellent metering and is the powder of choice for .270, 7mm magnum and .300 Win Mag. Excellent metering, accurate and consistent in most magnum rifles.

Lee's PaceSetter 3-Die Set includes a Full Length Sizing Die, Easy Adjust Dead Length Bullet Seating Die, Factory Crimp Die, Universal Shell Holder, Powder Dipper and instructions/load data.

Sierra has enhanced a segment of the MatchKing line by adding the acetal resin tip, thus crowning the Tipped MatchKing bullet line. The major advantage of adding a tip to the bullet is the reduction of drag, producing a more favorable ballistic...

Hornady's ELD-X bullet is a technologically advanced, match accurate, all range hunting bullet. It features highest in class ballistic coefficients and consistent, controlled expansion at all practical hunting distances. Its Heat Shield tip is immune to...

Lee Loader is a complete reloading system, kit includes everything needed to reload 44 Mag. except a rubber mallet.

SIERRA BULLETS .50 CAL .500400GR JSP 50CTFEATURES-.50 Caliber (.500)-400 grain -Bullet type: JSP-50 rounds/box-Sectional Density: .229Ballistic Coefficients and Velocity Ranges.185 @ 1600 fps and above.198 between 1600 and 1450 fps.212 between 1450 and...

RCBS TAPER CRIMP DIE 350LEGEND GROUP-C !

RCBS TRIM PRO 3-WAY CUTTER6.5MM CALIBERFEATURES:-Unique three-blade head configuration trims cases like the standard cutting tool, but in addition totrimming to length, inside blades chamfer the case while an outside blade deburrs it-The 3-way cutter...

NOSLER BULLETS 270 CAL .277140GR BALLISTIC TIP 50CTFEATURES-Caliber: .270-Diameter: .277"-140 Grain-Bullet Type: Ballistic tip hunting-Base: Boat tail-Spitzer point-Yellow polymer tip-Ballistic Coefficient: .456-50 rounds/box

HODGDON LIL'GUN 4LB. CAN !FEATURES:-4 lb. canister-Designed for 410-bore shotshell reloaders-Designed to fit, meter and perform flawlessly-Lil’ Gun has many magnum pistol applications and is a superb choice for reloading the 22 Hornet

ALLIANT POWDER GREEN DOT 8LBCAN ! 2CAN/CSFEATURES-8 pound -Principal Purpose: Handicap trap loads -Secondary Uses: Light 20 ga. target loads-Lower felt recoil-Superior patterning-Versatile for target and field

LEE FULL LENGTH 2-DIE SET43 SPANISHFEATURES-Full length 2 die set for .43 Spanish-Full length sizing die-Bullet seating die-Universal shell holder-Powder dipper-Instructions/load data

LEE SIX CAVITY MOLD9MM 120GR TC NO HANDLESFEATURES-Six Cavity Mold-.356 Diameter-120 grain-Truncated Cone nose bullet-Suitable for cartridges like 9mm Luger, .38 Super Auto, etc.-Lube & handles sold separately

TOP BRASS ONCE FIRED UNPRIMEDBRASS 40 SW 1000 PACK JUG!

LYMAN CASE HEAD SPACE GAUGE44 REMINGTON MAGNUMFEATURES:-Caliber: .44 Remington Magnum-Simply insert the case into the gauge to insure that it does not exceed the maximum or fall below the minimum allowable headspace-the gauge witll identify a case which...

LYMAN TURBO MEDIA SEPARATORCRANK OPERATEDFEATURES-Free spinning crank handle cover-Improved latches for a tight lock-up of the basket & cover-Can be used with either right or left hand-Tight seal to trap media and dust inside

HSM BULLETS .45LC CAL. .452200GR HARD LEAD-RNFP 250CT

PETERSON UNPRIMED CASES300 WIN MAG 50PACK 10BX/CS

HSM BULLETS .38-55 CAL. 378240GR HARD LEAD-RNFP 250CT

Winchester shellcases are engineered to precise tolerances to ensure smooth-feeding and positive chambering.

This smokeless spherical powder originated as a military powder, used for the 5.56 NATO or 223 Remington as handloaders know it. It sees a lot of use in the 222 Remington, 223 Remington and other small cartridges.

Lee's Carbide 3-Die Set includes Carbide Full Length Sizing Die, Powder Thru Expanding Die, Universal Shell Holder, Powder Dipper and instructions/load data.