Reloading Supplies

The Breech Lock Challenger press with the "O" frame is the strongest style press. The larger than average 4" opening allows for maximum hand clearance. The spent primer catcher is positive and allows you to route the spent primers directly to the trash...

Sub-X (Subsonic eXpanding) bullets deliver big results without a big bang. Designed to provide deep penetration below the speed of sound, Sub-X features a lead core. Long grooves in its gilding metal jacket combine with its flat profile and the patented...

Mec's progressive charge bar measures powder by volume before dropping into the hull. It then measures the shot to be dropped into the wad column.

RCBS Single Stage shell holders are built from hardened steel and designed to properly align the case with the reloading die in single-stage and turret presses. They're sized to fit specific case heads and capture 0.125 inch of the case head for proper...

Nosler Ballistic Tip Varmint bullets thrive on ultra-high velocity loads, yet will go the distance with spectacular results all the way down to the lowest practical velocity levels. Fast or slow, near or far, no matter what rifle/cartridge combination...

Lee's PaceSetter 3-Die Set includes a Full Length Sizing Die, Easy Adjust Dead Length Bullet Seating Die, Factory Crimp Die, Universal Shell Holder, Powder Dipper and instructions/load data.

Grips the shell for a firm fit in the press during reloading or priming operations. Universal shell holder used in most brands of reloading presses. Not for use with the Auto-Prime.

This bench mounted priming tool features a symmetrical design allows effortless right or left hand operation. Its comfortable lever with just the right amount of mechanical advantage seats even the most difficult primers with just finger pressure. It has...

Lee's Production Pot IV is a large, deep pot that holds approximately 10 pounds of lead and melts the lead less than 20 minutes. Its pour spout is up front where it belongs so you can see what you're doing and its uses only 500 watts of power during heat...

Lee's PaceSetter 3-Die Set includes a Full Length Sizing Die, Easy Adjust Dead Length Bullet Seating Die, Factory Crimp Die, Universal Shell Holder, Powder Dipper and instructions/load data.

Lee's Pro 1000 progressive 3-hole reloading kit for 9mm Luger includes press, dies (carbife full length size, powder through expanding and bullet seating dies), 3-hole turret, #19 shell plate, Pro Auto-Disk powder measure, universal case feeder and...

Varmageddon bullets are made with a lead-alloy core and feature a copper-alloy jacket designed to withstand high velocities yet expand immediately upon impact. Varmageddon bullets are manufactured using a highly efficient process, providing legendary...

Hornady's brass cases offers re-loaders excellent uniformity in wall thickness, weight, and internal capacity. The cases allow proper seating of the bullet, not only in the case, but in the chamber as well.

The RCBS Automatic Primer Feed Combo drops primers one at a time into the primer plug and sleeve. It helps stop misfires, as greasy fingers never need to touch primers, and the nylon primer pick-up keeps primers from falling out. It has a tube capacity...

This Factory Die incorporates a collet to apply a rifle type crimp to the case, which makes these very difficult to crimp cartridges a delight to reload. Bullets do not need a crimp groove, as the collet is so powerful it will form one.

The Classic Turret features the solid steel linkage of the Lee Classic Cast. The long stroke allows rifle cases over three inches long to be loaded using the automatic index. Deactivate the Auto-Index and cases over 4" can be loaded. The rigid cast iron...

The Lock-N-Load Sonic Cleaner 2 Liter features an 80 watt ceramic heater that enhances cleaning action and especially helps when cleaning gun parts. Its large two liter stainless steel tank holds up to three hundred .223 cases or one hundred fifty 308...

Designed for hunting, self-defense and law enforcement applications, the XTP bullet demonstrates the kind of accuracy that led many competitive shooters to adopt it. The stopping power of the XTP bullet has a truly built its world-class reputation...

RCBS NECK SIZER DIE ONLY 223REMINGTONFEATURES:-.223 Rem.-Resizes the case neck only (it doesn't touch the shoulder or body) & deprimes

LEE X-PRESS SHELLHOLDER #4

HARVESTER SCORPION 50 CAL240GR .451 FUNNEL POINT 12PKFEATURES-12 pack-.50 caliber sabot-240 grain-.451 funnel point MAG bullet-Excellent expansion & take-down power-Packaged with Crush Rib Sabots-Easy loading

CVA RAPID LOADER 54CAL 3 PACKPLASTICFEATURES-.54 caliber-3 per pack-Red-Straight through tube allows for loading ball, patch & powder in one fluid motion

LEE TRIMMER GAUGE 38 SW!FEATURES-For .38 Smith & Wesson-Case Length Gauge-Precise, easy way to trim to length & square the case mouth-Used with the Cutter & Lock Stud or Zip Trim

LEE DOUBLE CAVITY MOLD.350 BALL ALUMINUM!FEATURES-Double Cavity Mold-Produces a .350 diameter ball-64.36 grains-Includes handles

LYMAN CASE LOADING BLOCKREVERSIBLEFEATURES-Essential accessory for organization & speed-Holds 50 rifle or pistol cases .22 through .45 caliber-Molded of heavy duty plastic

ALLIANT POWDER 20/28 8LB CAN2CAN/CSFEATURES-8 pound-Principal Purpose: 20 and 28 gauge target loads -Powder of choice for 20 and 28 gauge target loads-Designed for Skeet and Sporting Clays-Competition-grade performance-Extremely clean burning-Designed...

This die body works with Lee's Deluxe Quick Trim Case Trimmer to quickly and precisely trim brass to the correct length at the same time it chamfers the inside and outside of the case mouth. No calipers, measurement or adjustment required. Simply install...

The RCBS Primer Pocket Swager has been redesigned to fit a larger group of cases. The swaging rods are made from stronger, high-tensile steel, more than doubling the strength of the original design. NOTE: Not for use on progressive presses.

Hornady's Custom-Grade Dies provide a lifetime of reloading. They are so well-crafted that they are guaranteed never to break or wear out from normal use. The Sip Spindle design features a series of light threads cut on the spindle and spindle collet...

RCBS's 3-Die Carbide Sets is for straight-wall rifle and pistol cases. The Carbide Sizer Die sizes the case and de-primes (the carbide sizer ring eliminates the need to lubricate). Its Expander Die expands the case to the proper diameter to accept the...

The smokeless Ball Powder 231 is ideally suited to the 38 special, 45 Auto and 9mm standard loads. Consistency, clean burning, low flash, and a broad range of applications make this powder a choice for any pistol cartridge reloader.

000 Buckshot precision-machined mold produces 18 linked pellets per cast. .360 diameter, 70 grains weight. Each cast produces enough pellets to load two 12 Gauge shotshells. It easily casts 3,000 pellets per hour. *Note- Does NOT include handles. Handles...

High Gun is a flattened, spherical shotshell powder designed for light-target, handicap and super handicap loads in a 12-gauge shotgun. This powder also closely duplicates Remington Nitro 27 factory loads. High Guns geometry results in a powder that...

The 9000GN Auto-Dex press has everything you need for high-speed, efficient operation and unbeatable precision. The multiple operations at six stations speedily produce a finished shell with every stroke of the handle. It has a fully automatic primer...

Hornady's Match bullets features the revolutionary AMP (Advanced Manufacturing Process) bullet jacket. The bullet jackets are a technological advancement in design, tooling, and manufacturing that combine to produce the most consistently concentric...

Lee 270 WIN Case Length Gauge is a precise, easy way to trim to length and square the case mouth. Used with the Cutter and Lock Stud or Zip Trim. Trim to length 2.520 to 2.540 inches.

This Factory Die incorporates a collet to apply a rifle type crimp to the case, which makes these very difficult to crimp cartridges a delight to reload. Bullets do not need a crimp groove, as the collet is so powerful it will form one.

Lee's Carbide 3-Die Set includes Carbide Full Length Sizing Die, Powder Thru Expanding Die, Universal Shell Holder, Powder Dipper and instructions/load data.

Hornady Lock-N-Load Bullet tubes can fit 40 plus bullets depending on caliber and weight and feature a milled window for visual bullet level inspection. Lock-N-Load Bullet Tubes are sold in packs of 3 tubes per caliber. Lock-N-Load Bullet Tube feed...

The Hornady Traditional Varmint bullets features a streamlined design for flat trajectory. Its lead core and match-grade copper jacket represent the original standard created by Joyce Hornady for classic varmint hunting. Primarily comprised of spire...